Overview
Mono-layer Flow Casting Film Plastic Ps Foam Sheet Extrusion Production Line Board Making Machinery
(9) The three rollers should run at a speed slightly higher than the extrusion speed of the slab from the mouth of the mold, the general speed difference does not exceed 10%. Three rollers should be controlled at a smooth working speed, too fast or too slow running speed on the thickness of the plate have a greater impact on the error.
(10) polyolefin plastics extrusion molding plate (sheet) material, screw selection of mutant structure, compression ratio of (3-4):1, melt flow rate: HDPE 0.3 ~ 2.0g/10min, LDPE 0.1 ~ 0.3g/1Omin, PP 0.5 ~ 1.5g/10min. ABS and other non-crystalline polymer resin extrusion molding plate (sheet) material, should use a gradient screw. Should be used gradient screw, compression ratio of (1.6 a 2.5):1.
(11) plastic plate (sheet) of extrusion molding, in addition to polyvinyl chloride, polyethylene and polypropylene resin extrusion before the general circumstances do not dehumidification treatment, some other plastics (such as ABS, polyamide, etc.) should be required in the extrusion of dehumidification and drying before processing. Otherwise, an exhaust-type extruder should be used for extrusion molding.
Product Description
 | 1. Technical parameters: 1. Barrel material rod: Φ100mm Aspect ratio: 32:1 Material: 38CrMoAl, Quenching and tempering, surface nitriding, with exclusive mixing section, good mixing effect and large discharge volume 2. Hanger type mould Material: 38CrMoAl, after quenching and tempering treatment, has good toughness and hardness, high temperature and frequent use without deformation 3. The extruder reducer adopts airtightness, good reliability and strength hard tooth surface reducer 4. Intelligent temperature control system 5. Applicable substrates: roll paper, non-woven fabric, chemical fiber cloth, etc. 6. Coating material: PE, PP, LDPE, LLDPE, HDPE, EVA, EMA and other resins |
7. Lamination width: 600mm~2800mm; 8. Coating thickness: 0.015mm~0.030mm 9. Coating uniformity: error ±5%; 10. Peel strength: 3~5N/30mm (according to the actual coating substrate) 11. The maximum extrusion capacity of the laminating machine: 200kg/h; 12. Mechanical line speed of laminating machine: 0~150m/min; 13. Double station unwinding, magnetic powder tension unwinding 14. Film thickness gauge, automatic measurement 15. Total installed capacity: about 150kw; 16. The total weight of the laminating machine unit: about 18 tons The above parameters of the composite laminating machine are for reference and can be customized. After-sales service: The main parts are guaranteed for one year, and free door-to-door installation and debugging |  |
Application Field
Spcification
| Model | SMST004 |
| Item number | According to the contract number |
| Product alias | PP PLA PS sheet machine |
| Product use | PP sheet can be used in stationery, food and drug gift packaging, lighting lampshades, electronic packaging boxes, etc. |
| Type | Sheet Extruder |
| Number of screws | Single screw |
| Screw diameter | 130 (mm) / can be customized |
| Maximum extrusion diameter | 1600 (mm) / can be customized |
| Production capacity | 100-180 (Kg/h) |
| Positioning accuracy | 0.2-2 (mm) |
| Dimensions | 17000*3000*2800 (mm) |
| Motor power | 156 (kw) |
| After-sales service | The main parts are guaranteed for one year, and free door-to-door installation and debugging |
Overview
Mono-layer Flow Casting Film Plastic Ps Foam Sheet Extrusion Production Line Board Making Machinery
(9) The three rollers should run at a speed slightly higher than the extrusion speed of the slab from the mouth of the mold, the general speed difference does not exceed 10%. Three rollers should be controlled at a smooth working speed, too fast or too slow running speed on the thickness of the plate have a greater impact on the error.
(10) polyolefin plastics extrusion molding plate (sheet) material, screw selection of mutant structure, compression ratio of (3-4):1, melt flow rate: HDPE 0.3 ~ 2.0g/10min, LDPE 0.1 ~ 0.3g/1Omin, PP 0.5 ~ 1.5g/10min. ABS and other non-crystalline polymer resin extrusion molding plate (sheet) material, should use a gradient screw. Should be used gradient screw, compression ratio of (1.6 a 2.5):1.
(11) plastic plate (sheet) of extrusion molding, in addition to polyvinyl chloride, polyethylene and polypropylene resin extrusion before the general circumstances do not dehumidification treatment, some other plastics (such as ABS, polyamide, etc.) should be required in the extrusion of dehumidification and drying before processing. Otherwise, an exhaust-type extruder should be used for extrusion molding.
Product Description
| 1. Technical parameters: 1. Barrel material rod: Φ100mm Aspect ratio: 32:1 Material: 38CrMoAl, Quenching and tempering, surface nitriding, with exclusive mixing section, good mixing effect and large discharge volume 2. Hanger type mould Material: 38CrMoAl, after quenching and tempering treatment, has good toughness and hardness, high temperature and frequent use without deformation 3. The extruder reducer adopts airtightness, good reliability and strength hard tooth surface reducer 4. Intelligent temperature control system 5. Applicable substrates: roll paper, non-woven fabric, chemical fiber cloth, etc. 6. Coating material: PE, PP, LDPE, LLDPE, HDPE, EVA, EMA and other resins |
7. Lamination width: 600mm~2800mm; 8. Coating thickness: 0.015mm~0.030mm 9. Coating uniformity: error ±5%; 10. Peel strength: 3~5N/30mm (according to the actual coating substrate) 11. The maximum extrusion capacity of the laminating machine: 200kg/h; 12. Mechanical line speed of laminating machine: 0~150m/min; 13. Double station unwinding, magnetic powder tension unwinding 14. Film thickness gauge, automatic measurement 15. Total installed capacity: about 150kw; 16. The total weight of the laminating machine unit: about 18 tons The above parameters of the composite laminating machine are for reference and can be customized. After-sales service: The main parts are guaranteed for one year, and free door-to-door installation and debugging | |
Application Field
Spcification
| Model | SMST004 |
| Item number | According to the contract number |
| Product alias | PP PLA PS sheet machine |
| Product use | PP sheet can be used in stationery, food and drug gift packaging, lighting lampshades, electronic packaging boxes, etc. |
| Type | Sheet Extruder |
| Number of screws | Single screw |
| Screw diameter | 130 (mm) / can be customized |
| Maximum extrusion diameter | 1600 (mm) / can be customized |
| Production capacity | 100-180 (Kg/h) |
| Positioning accuracy | 0.2-2 (mm) |
| Dimensions | 17000*3000*2800 (mm) |
| Motor power | 156 (kw) |
| After-sales service | The main parts are guaranteed for one year, and free door-to-door installation and debugging |
