Overview
Plastic Pp/pe/abs Sheet Making Machine
(5) Note that the roughness of the working surface of the three rollers R should not be greater than 0. 2 pm. clean up the roll surface is not allowed to use hard steel knife to scratch the roll surface, should use copper knife to clean up the roll surface residue.
(6) The roll surface should have some height; the gap between the three rolls should be equal to or slightly greater than the thickness of the plate.
(7) Molding mold temperature control should be stable. When the temperature is high, the melt flows faster in the mold; when the temperature is low, the melt flows slower in the mold. Unstable melt flow rate will cause the longitudinal thickness error of the plate (sheet) products.
(8) pay attention to the control of the three rollers of the working surface temperature, should be into the roll temperature is slightly higher, out of the roll temperature is slightly lower. Roll surface temperature is high, the slab is not easy to get off the roller, the surface of the product is easy to produce horizontal lines; temperature is low, the surface of the product is not glossy. According to this phenomenon, the roll surface temperature control should be adjusted in time.
Product Description
 | 1. Technical parameters: 1. Barrel material rod: Φ100mm Aspect ratio: 32:1 Material: 38CrMoAl, Quenching and tempering, surface nitriding, with exclusive mixing section, good mixing effect and large discharge volume 2. Hanger type mould Material: 38CrMoAl, after quenching and tempering treatment, has good toughness and hardness, high temperature and frequent use without deformation 3. The extruder reducer adopts airtightness, good reliability and strength hard tooth surface reducer 4. Intelligent temperature control system 5. Applicable substrates: roll paper, non-woven fabric, chemical fiber cloth, etc. 6. Coating material: PE, PP, LDPE, LLDPE, HDPE, EVA, EMA and other resins |
7. Lamination width: 600mm~2800mm; 8. Coating thickness: 0.015mm~0.030mm 9. Coating uniformity: error ±5%; 10. Peel strength: 3~5N/30mm (according to the actual coating substrate) 11. The maximum extrusion capacity of the laminating machine: 200kg/h; 12. Mechanical line speed of laminating machine: 0~150m/min; 13. Double station unwinding, magnetic powder tension unwinding 14. Film thickness gauge, automatic measurement 15. Total installed capacity: about 150kw; 16. The total weight of the laminating machine unit: about 18 tons The above parameters of the composite laminating machine are for reference and can be customized. After-sales service: The main parts are guaranteed for one year, and free door-to-door installation and debugging |  |
Application Field
Spcification
| Model | SMST004 |
| Item number | According to the contract number |
| Product alias | PP PLA PS sheet machine |
| Product use | PP sheet can be used in stationery, food and drug gift packaging, lighting lampshades, electronic packaging boxes, etc. |
| Type | Sheet Extruder |
| Number of screws | Single screw |
| Screw diameter | 130 (mm) / can be customized |
| Maximum extrusion diameter | 1600 (mm) / can be customized |
| Production capacity | 100-180 (Kg/h) |
| Positioning accuracy | 0.2-2 (mm) |
| Dimensions | 17000*3000*2800 (mm) |
| Motor power | 156 (kw) |
| After-sales service | The main parts are guaranteed for one year, and free door-to-door installation and debugging |
Overview
Plastic Pp/pe/abs Sheet Making Machine
(5) Note that the roughness of the working surface of the three rollers R should not be greater than 0. 2 pm. clean up the roll surface is not allowed to use hard steel knife to scratch the roll surface, should use copper knife to clean up the roll surface residue.
(6) The roll surface should have some height; the gap between the three rolls should be equal to or slightly greater than the thickness of the plate.
(7) Molding mold temperature control should be stable. When the temperature is high, the melt flows faster in the mold; when the temperature is low, the melt flows slower in the mold. Unstable melt flow rate will cause the longitudinal thickness error of the plate (sheet) products.
(8) pay attention to the control of the three rollers of the working surface temperature, should be into the roll temperature is slightly higher, out of the roll temperature is slightly lower. Roll surface temperature is high, the slab is not easy to get off the roller, the surface of the product is easy to produce horizontal lines; temperature is low, the surface of the product is not glossy. According to this phenomenon, the roll surface temperature control should be adjusted in time.
Product Description
| 1. Technical parameters: 1. Barrel material rod: Φ100mm Aspect ratio: 32:1 Material: 38CrMoAl, Quenching and tempering, surface nitriding, with exclusive mixing section, good mixing effect and large discharge volume 2. Hanger type mould Material: 38CrMoAl, after quenching and tempering treatment, has good toughness and hardness, high temperature and frequent use without deformation 3. The extruder reducer adopts airtightness, good reliability and strength hard tooth surface reducer 4. Intelligent temperature control system 5. Applicable substrates: roll paper, non-woven fabric, chemical fiber cloth, etc. 6. Coating material: PE, PP, LDPE, LLDPE, HDPE, EVA, EMA and other resins |
7. Lamination width: 600mm~2800mm; 8. Coating thickness: 0.015mm~0.030mm 9. Coating uniformity: error ±5%; 10. Peel strength: 3~5N/30mm (according to the actual coating substrate) 11. The maximum extrusion capacity of the laminating machine: 200kg/h; 12. Mechanical line speed of laminating machine: 0~150m/min; 13. Double station unwinding, magnetic powder tension unwinding 14. Film thickness gauge, automatic measurement 15. Total installed capacity: about 150kw; 16. The total weight of the laminating machine unit: about 18 tons The above parameters of the composite laminating machine are for reference and can be customized. After-sales service: The main parts are guaranteed for one year, and free door-to-door installation and debugging | |
Application Field
Spcification
| Model | SMST004 |
| Item number | According to the contract number |
| Product alias | PP PLA PS sheet machine |
| Product use | PP sheet can be used in stationery, food and drug gift packaging, lighting lampshades, electronic packaging boxes, etc. |
| Type | Sheet Extruder |
| Number of screws | Single screw |
| Screw diameter | 130 (mm) / can be customized |
| Maximum extrusion diameter | 1600 (mm) / can be customized |
| Production capacity | 100-180 (Kg/h) |
| Positioning accuracy | 0.2-2 (mm) |
| Dimensions | 17000*3000*2800 (mm) |
| Motor power | 156 (kw) |
| After-sales service | The main parts are guaranteed for one year, and free door-to-door installation and debugging |
